Conclusions and recommendations
If there aren’t any recommendations to be made as a consequence of the project, just call this section Conclusions.
The Conclusions section sums up the important thing points of one’s discussion, the essential features of your design, or even the significant outcomes of your investigation. As its function would be to round from the story of assembling your project, it will:
- be written to relate right to the aims associated with project as stated into the Introduction
- indicate the extent to which the aims have been achieved
- summarise the findings that are key outcomes or information in your report
- acknowledge limitations and then make suggestions for future work (where applicable)
- Highlight the usefulness or significance of your work.
The conclusions should relate solely to the aims of the work:
The purpose of this project is always to design a cell phone tower for a suburban location..
The mobile phone tower presented here could be erected safely in a suburban street.
It entails a complete part of no more than 2m 2 l, and has now the following safety features.
This investigation will review the quantity of passengers utilizing the Monash University Clayton-Caulfield inter-campus bus to be able to recommend adjustments into the ongoing service if needed.
Analysis of the survey data obtained in this project shows that usage of the Clayton-Caulfield inter-campus bus has grown by 24% in the past five years. It is strongly recommended that frequency be increased during peak usage.
The Conclusions section below is from a level 2 Civil Engineering Alternative Designs report presenting two designs for a an overpass bridge. Click on the buttons that are coloured begin to see the comments.
Each one of the two bridge designs Lecturer’s comment:
An elegant beginning for a Conclusions follows on neatly from the discussion that is preceding. In this full case, in addition it indicates that the aims of the project have now been met. presented in this report fulfil the criteria specified into the project brief. Both designs Lecturer’s comment:
The main findings or outcomes – in this full case the key options that come with the designs – are then recapped. Incorporate piers that are round piled foundations, which are used because the soil conditions are unknown and possibly unstable. Design 1, a simple i-girder that is composite, has got the benefit of being manufactured from steel and thus has longer spans and essay writer fewer piers.
Design 2, a super-T beam br >Design 2 Lecturer’s comment:
The need for the results – in this case the last recommendation – is clearly stated. is therefore recommended. It offers Lecturer’s comment:
To finish off, the achievement for the project is reinforced. An overpass that is affordable superior durability, and fully meets the requirements associated with the design brief.
Always address limitations and suggest how they may be overcome in the future work. The below that is excerpt through the Conclusions of a study on a project investigating the effect of pulsation on heat transfer in horizontal pipe flow.
Experimental results Lecturer’s comment:
Key conclusions drawn through the project. revealed that pulsed flow without flow reversal had no significant effect compared with steady flow. Preliminary experiments with reversed flow, however, clearly indicated increased heat transfer. It is likely due Lecturer’s comment:
Provide a possible explanation for notable results, especially unexpected ones. into the large disturbances within the hydrodynamic boundary layer when the flow changes direction. Further research Lecturer’s comment:
Recommend further research to deal with any work that is extra think could be useful. is advised to determine the utmost achievable enhancement.
It should be noted that Lecturer’s comment:
Acknowledge limitations or errors and suggest explanations and/or solutions. the experimental results do not concur with the equations that are theoretical. This can be due to the deposits which developed inside the pipe, or even to thermocouple temperature that is inconsistent. Therefore, regular inspection of this test rig is preferred.
For an extremely report that is long it really is acceptable to present the conclusions and recommendations in point form:
The prototype robot courier presented here has been shown to allow you to delivering documents autonomously in an working office environment. It offers demonstrated the next the different parts of mobile robotics:
- Localisation: The Kalman localisation that is filter-based achieved sub-centimeter accuracy under normal operating conditions.
- Environment modelling: The occupancy map was updated dynamically to include obstacles not within the map that is original.
- Path planning: A distance path that is transform-based using obstacle transforms produced a globally optimal local entrapment-free path to the target.